knowledge:3d_print:2022052401
差别
这里会显示出您选择的修订版和当前版本之间的差别。
后一修订版 | 前一修订版 | ||
knowledge:3d_print:2022052401 [2022/05/24 01:26] – 创建 弘毅 | knowledge:3d_print:2022052401 [2023/06/07 04:23] (当前版本) – 外部编辑 127.0.0.1 | ||
---|---|---|---|
行 1: | 行 1: | ||
====== Prusa MK3S 开始与结束G-code研究 ====== | ====== Prusa MK3S 开始与结束G-code研究 ====== | ||
+ | ===== 初始 ===== | ||
+ | < | ||
+ | M862.3 P " | ||
+ | M862.1 P[nozzle_diameter] ; 检查喷嘴直径 | ||
+ | M115 U3.10.1 ; 打印固件信息,告诉打印机最新的固件版本,与打印机版本进行对比,如果打印机版本低会提时升级 | ||
+ | G90 ; 使用绝对坐标模式 | ||
+ | M83 ; E轴挤出机设置为相对模式 | ||
+ | M104 S[first_layer_temperature] ; 设置喷嘴温度为首层打印温度 | ||
+ | M140 S[first_layer_bed_temperature] ; 设置热床温度为打印首层热床温度 | ||
+ | M190 S[first_layer_bed_temperature] ; 等待热床温度达到打印首层温度 | ||
+ | M109 S[first_layer_temperature] ; 等待喷嘴温度到达首层打印温度 | ||
+ | G28 W ; 无网床调平归为所有轴 | ||
+ | G80 ; 网床调平 | ||
+ | G1 Z0.2 F720 // | ||
+ | G1 Y-3 F1000 ; go outside print area// | ||
+ | G92 E0// | ||
+ | G1 X60 E9 F1000 ; intro line// | ||
+ | G1 X100 E12.5 F1000 ; intro line// | ||
+ | G92 E0// | ||
+ | M221 S{if layer_height< | ||
+ | |||
+ | ; Don't change E values below. Excessive value can damage the printer. | ||
+ | {if print_settings_id=~/ | ||
+ | {if print_settings_id=~/ | ||
+ | </ | ||
+ | ===== 结尾 ===== | ||
+ | < | ||
+ | G4 ; wait// | ||
+ | M221 S100 ; reset flow // | ||
+ | M900 K0 ; reset LA //设置K 因子为0,重置LA | ||
+ | {if print_settings_id=~/ | ||
+ | M104 S0 ; turn off temperature// | ||
+ | M140 S0 ; turn off heatbed设置床温,关闭加热床 | ||
+ | M107 ; turn off fan// | ||
+ | {if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+30, | ||
+ | G1 X0 Y200 F3000 ; home X axis// | ||
+ | M84 ; disable motors | ||
+ | </ | ||
+ | ====== 在图层G代码更改之前 ====== | ||
+ | < | ||
+ | ; | ||
+ | G92 E0.0新的挤出机位置0.0 | ||
+ | ; | ||
+ | </ | ||
+ | ====== 图层更改G代码之后 ====== | ||
+ | < | ||
+ | ; | ||
+ | ; | ||
+ | </ | ||
+ | |||
knowledge/3d_print/2022052401.1653355615.txt · 最后更改: 2023/06/07 04:09 (外部编辑)