用户工具

站点工具


en:learing:examples:string_comparison_operators

String Comparison Operators

The String comparison operators ==, !=,>, < ,>=, ⇐ , and the equals() and equalsIgnoreCase() methods allow you to make alphabetic comparisons between Strings. They're useful for sorting and alphabetizing, among other things.

The operator == and the method equals() perform identically. In other words,

if (stringOne.equals(stringTwo)) {

is identical to

if (stringOne ==stringTwo) {

The “>” (greater than) and “<” (less than) operators evaluate strings in alphabetical order, on the first character where the two differ. So, for example “a” < “b” and “1” < “2”, but “999” > “1000” because 9 comes after 1.

Caution: String comparison operators can be confusing when you're comparing numeric strings, because the numbers are treated as strings and not as numbers. If you need to compare numbers, compare them as ints, floats, or longs, and not as Strings.

Hardware Required

Arduino or Genuino Board Circuit

There is no circuit for this example, though your board must be connected to your computer via USB and the serial monitor window of the Arduino Software (IDE) should be open.

image developed using Fritzing. For more circuit examples, see the Fritzing project page

Code

/*
  Comparing Strings
 
 Examples of how to compare strings using the comparison operators
 
 created 27 July 2010
 modified 2 Apr 2012
 by Tom Igoe
 
 http://www.arduino.cc/en/Tutorial/StringComparisonOperators
 
 This example code is in the public domain.
 */
 
String stringOne, stringTwo;
 
void setup() {
  // Open serial communications and wait for port to open:
  Serial.begin(9600);
  while (!Serial) {
    ; // wait for serial port to connect. Needed for Leonardo only
  }
 
 
  stringOne = String("this");
  stringTwo = String("that");
  // send an intro:
  Serial.println("\n\nComparing Strings:");
  Serial.println();
 
}
 
void loop() {
  // two strings equal:
  if (stringOne == "this") {
    Serial.println("StringOne == \"this\"");
  }
  // two strings not equal:
  if (stringOne != stringTwo) {
    Serial.println(stringOne + " =! " + stringTwo);
  }
 
  // two strings not equal (case sensitivity matters):
  stringOne = "This";
  stringTwo = "this";
  if (stringOne != stringTwo) {
    Serial.println(stringOne + " =! " + stringTwo);
  }
  // you can also use equals() to see if two strings are the same:
  if (stringOne.equals(stringTwo)) {
    Serial.println(stringOne + " equals " + stringTwo);
  } else {
    Serial.println(stringOne + " does not equal " + stringTwo);
  }
 
  // or perhaps you want to ignore case:
  if (stringOne.equalsIgnoreCase(stringTwo)) {
    Serial.println(stringOne + " equals (ignoring case) " + stringTwo);
  } else {
    Serial.println(stringOne + " does not equal (ignoring case) " + stringTwo);
  }
 
  // a numeric string compared to the number it represents:
  stringOne = "1";
  int numberOne = 1;
  if (stringOne.toInt() == numberOne) {
    Serial.println(stringOne + " = " + numberOne);
  }
 
 
 
  // two numeric strings compared:
  stringOne = "2";
  stringTwo = "1";
  if (stringOne >= stringTwo) {
    Serial.println(stringOne + " >= " + stringTwo);
  }
 
  // comparison operators can be used to compare strings for alphabetic sorting too:
  stringOne = String("Brown");
  if (stringOne < "Charles") {
    Serial.println(stringOne + " < Charles");
  }
 
  if (stringOne > "Adams") {
    Serial.println(stringOne + " > Adams");
  }
 
  if (stringOne <= "Browne") {
    Serial.println(stringOne + " <= Browne");
  }
 
 
  if (stringOne >= "Brow") {
    Serial.println(stringOne + " >= Brow");
  }
 
  // the compareTo() operator also allows you to compare strings
  // it evaluates on the first character that's different.
  // if the first character of the string you're comparing to
  // comes first in alphanumeric order, then compareTo() is greater than 0:
  stringOne = "Cucumber";
  stringTwo = "Cucuracha";
  if (stringOne.compareTo(stringTwo) < 0) {
    Serial.println(stringOne + " comes before " + stringTwo);
  } else {
    Serial.println(stringOne + " comes after " + stringTwo);
  }
 
  delay(10000);  // because the next part is a loop:
 
  // compareTo() is handy when you've got strings with numbers in them too:
 
  while (true) {
    stringOne = "Sensor: ";
    stringTwo = "Sensor: ";
 
    stringOne += analogRead(A0);
    stringTwo += analogRead(A5);
 
    if (stringOne.compareTo(stringTwo) < 0) {
      Serial.println(stringOne + " comes before " + stringTwo);
    } else {
      Serial.println(stringOne + " comes after " + stringTwo);
 
    }
  }
}
en/learing/examples/string_comparison_operators.txt · 最后更改: 2023/06/07 04:23 由 127.0.0.1